Abstract

Batik is one of the works owned by the Indonesian Nation, which has noble values and is recognized by other nations. The rapid development of batik makes batik makers need to pay attention to the production process carried out, In carrying out the activities of making stamped batik, it has not been supported by a special work table. Still using an ordinary stamp table that is less comfortable to use for stamped batik. So that in doing their work craftsmen have low productivity and efficiency. This research was conducted at PT XYZ to evaluate and reduce the risk of musculoskeletal disorders in stamped batik makers through ergonomic work table redesign. The research method used is case study-based quantitative, with a population of PT XYZ employees who work as stamped batik makers. Primary data was collected through observation, questionnaires and interviews. Posture measurements were carried out using the NBM (Nordic Body Map) questionnaire, to determine musculoskeletal complaints including 28 muscle parts in the musculoskeletal system on both sides of the body right and left. Then posture measurements were taken using the REBA (Rapid Entire Body Assesment) method. The results of the NBM questionnaire showed that before the improvement of the stamp batik had a high chart of complaints of pain in the musculoskeletal muscles and also the results of the REBA score showed a high risk of musculoskeletal disorders, especially in the neck, shoulders, bronze, arms and legs. After the implementation of a more comfortable stamp work table design and stamp stove table (Adjustable) there was a significant decrease in the REBA score decreasing from 8 to 1. This shows a significant reduction in the risk of musculoskeletal disorders, so that ergonomic work table design can reduce the risk of musculoskeletal disorders at PT XYZ and increase worker comfort.

Keywords:

Ergonomic cap table, Muskuloskeletal Disorders, Nordic Body Map, Rapid entire Body assesment.

References:

1) Agus Setiawan, A. S. (2019). Implementasi Recycle Limbah Kayu Hasil Produksi Plywood Dan Work Wood. Journal Knowledge Industrial Engineering (JKIE), 121-127.

2) Andriani, D.P., & Sugiono. 2017. Penjadwalan Waktu Istirahat Optimal untuk Mengurangi Risiko Muscoloskeletal Disorders berdasarkan OCRA Index. Jurnal lmiah Teknik Industri, Vol. 15 (2): 157-167.

3) Bridger, R.S., 1995. Introduction to Ergonomics E. M. Munson & J. W. Bradley, eds, Singapore: McGraw-Hill Book Co.

4) Budiyanto Tri, & Agus, S. (2021). Designing an Ergonomic-Based Work Facility of Dough Stirrer for Kerupuk Cipir Using Rapid Entire Body Assesment (REBA) Analysis to Reduce Muskuloskeletal Complaints and Increase Productivity. Logic : Jurnal Rancang Bangun Dan Teknologi, 21(2), 87–92. https://doi.org/10.31940/logic.v21i2.2454.

5) Dewi, N.F. 2020. Identifikassi Risiko Ergonomi Dengan Metode Nordic Body Map Terhadap Perawat Poli RS X. Jurnal Sosial Humaniora Terapan. 2(2): 125-134.

6) Fitri, M. I. Adelino, dan F. A. Putra, Usulan Perancangan Kursi Plus Meja Ergonomis Dengan Pendekatan Antropometri, Menara Ilmu, Vol. Xv No.01 Juli, 2021

7) Haekal, J, Hanum, B, (2020), International Journal Of Engineering Research and Advance Technology ( IJERAT), 6(7), 27-36, STUDY OF PHARMACEUTICAL COMPANY IN BOGOR, INDONESIA.

8) Heny Agustina.L, (2020). Pengembangan Desain Sistem Kerja Pengrajin Canting Cap Batik Dengan Metode Ergonomi Partisipatori, universitas islam indonesia yogjakarta.

9) Hidayatullah, I. F., & Mahbubah, N. A. (2021). Evaluasi Postur Kerja Operator Penggilingan Kelapa Berbasis Metode Workplace Ergonomic Risk Assesment Dan Job Strain Index. Radial, 9(2), 135–151. https://doi.org/https://doi.org/10.37971/radial.v9i2.230

10) Humantech, I., 1995. Applied Ergonomic Training Manual: Prepered for Procter & Gamble Inc. 2nd Editio., Australia: berkeley Vale.

11) Kurnianto dan Y Andrian, Perancangan Meja Kerja Yang Ergonomis Untuk Membantu Proses Repair Stripping Mirrors Dengan Metode Rula, Volume X. No. 2. September 2020, Issn 2088-060x

12) Lueder, R. (1995), A Proposed RULA for Computer Users, Proccedings of the Ergonomics Summer Workshop, UC berkeley Center for Occupational & Environmental Helth Continuing Program, san fransisco, August.

13) Pratiwi, P. A., Widyaningrum, D., & Jufriyanto, M. (2021). Analisis Postur Kerja Menggunakan Metode Reba Untuk Mengurangi Risiko Musculoskeletal Disorder (Msds). Profisiensi, 9(2), 205–214.

14) Purnomo, Hari. (2013). Anthropometry and its Application, First edition, Graha Ilmu Yogjakarta.

15) Ramadhan, M. 2019. Perancangan Meja dan Sofa yang Ergonomis dari Limbah Ban Mobil dengan Pendekatan Anthropometri. STITEKNAS: Jambi.

16) Suryatman.S.T dan R. Ramdani, Desain Kursi Santai Multifungsi Ergonomis Dengan Menggunakan Pendekatan Antropometri, Journal Industrial Manufacturing Vol. 4, No. 1, Januari 2019, Pp. 45- 54 P-Issn: 2502-4582, E-Issn: 2580-3794

17) Susanti, H, R Zadry, dan B. Yuliandra, Pengantar Ergonomi Industri, I. Padang, Andalas University Press Http://Repo.Unand.Ac.Id/28012/1/Buku%20pengantar%20ergonomi%20industri.Pdf . 2015.

18) Tiogana, dan N. Hartono, Analisis Postur Kerja Dengan Menggunakan Reba Dan Rula di PT X, Journal of Integrated System Vol 3. No. 1, Juni 2020: 9-25

19) Wijaya, P. G. (2019). Hubungan posisi dan lama duduk dengan nyeri punggung bawah pada pemain game online. Intisari Sains Medis 2019, Volume 10, Number 3: 834-839.

20) Yohanes, A, Ekonindiyo, F.A & Prihastono, E. ( 2023 ).Addition of Facilities to Bottle Capping Machine 1,2,3 Industrial Engineering, Universitas Stikubank, Semarang Indonesia.

21) Yudiardi, M. F., Imron, M., & Purwangka, F. (2021). Penilaian Postur Kerja Dan Risiko Musculoskeletal Disorders ( Msds ) Pada Nelayan Bagan Apung Dengan Menggunakan Metode Reba. Jurnal IPTEKS PSP, 8(April), 14–23.